Showing posts with label how to. Show all posts
Showing posts with label how to. Show all posts

Monday, February 28, 2011

How To: Mk II "Drax" Pattern Hydra

This tutorial is based off of the wonderful Hydra conversion created by Admiral Drax. I loved the look of the conversion as well as the price at which it could be acquired, but I wanted a bit more adaptability to my design. So, drawing on the pictures at his blog as well as my work with the "SandWyrm" pattern Chimeras I came up with the following conversion.

What you'll need:
1 Chimera kit
1 Aegis Defense Kit
At least 8" of 1/8" diameter wooden rod (obtainable at most hardware stores)
Plasticard
Possibly some modeling putty if you are as poor at crafts as I am.

Step 1: Form the basis of the turret
This part is pretty much straight out of the Aegis Defense kit instructions. Take the four sides of the turret base and put them together, then put the top of the turret (with the circular opening) on top. See the picture below for an example.

Step 2: Prepare the autocannons


The autocannons are not long enough, so we'll need to saw these apart after gluing the ammo barrels to the turrets. Make the incision just in front of the small targeting vane on the bottom of the autocanon barrels, then file down the newly formed edges. See the picture above for reference

Next we need to saw the wooden rod apart into 2" segments. File down the ends of the rods.

Now using a small dremel tool drill into the center of both ends of each wooden rod and into the interior surfaces of the autocannon barrels. Put small pieces of paper clips, gauge wire, etc. to act as pins, then super glue the three segments together as below.


Step 3: Attach the autocannons to the turret

Look on the sides of the paired autocannons for a circular knob. One of them has an additional cube jutting out from it, which you should saw off and file smooth.

Then, attach the autocannons to the sides of the turret like below. Make sure that the slanted side of the turret (the one with the tiny little window) is towards the front. I like to make mine slanted upwards a bit, but orient to your own taste

Step 4: Turret base and top

We're going to close off the top and bottom of the turret and make it so that it can rotate on top of our Chimera. Cut off a rectangular piece of plasticard that is [NUMBER] by [NUMBER] inches, then cut a circular hole in it that is [NUMBER] inches in diameter. It should fit snugly around the circular piece from the Aegis Defense kit pictured below. Make sure to save the circular piece that you cut out.


Superglue the piece of plasticard around the disc:


Next, attach that completed piece to the bottom of the turret.


Now take the circular piece of plasticard that you cut out from before and glue it on to the top of the turret.


Step 4: Start building the Chimera

Begin by building the base of the Chimera just as you would normally do so, but stop before gluing on the top of the Chimera.


Next, take the top part of the Chimera and saw it in three like below. The front part is along the line of rivets just behind the turret and the back part should be cut right where the bottom angles off of the straight line. This is a bit farther back than in the "SandWyrm" Chimeras but I think the extra bit of movement towards the rear of the vehicle makes the Hydra turret look more believable.


You can discard the middle section. Attach the front and rear sections to your Chimera hull, making sure to sand the edges of the rear and front edges to match cleanly with one another. I failed at this task, so be careful :)

You will need to cut out a few pieces of plasticard to cover up the rear hatch, forward hold and the tiny hole in the front, as seen below:

The small yellow piece is a small piece of metal ruler tape; I'll use it to swap in and out magnetized hull weapons.

Step 5: Done!

The Hydra turrets can be placed on top of the Chimera chassis and will fit snugly around where the normal Chimera turret would go. This way they can rotate freely and be easily swapped out with a normal Chimera turret if you so desire.

I've added a few bits from the Aegis defense kit onto the turrets to spruce them up, specifically the vox caster on the rear and the targeting sight on the front.


I hope you've enjoyed this tutorial, and many thanks of course go out to Drax and SandWyrm for giving me the basis of this conversion.

Wednesday, February 9, 2011

A Beginner's Guide to the Guard: Painting ye Average Guardsman

 Now, this won't be some kind of super-fancy guide to painting super awesome looking Guardsmen, as even I can't do that quite yet. This is just for those of us who want something that looks respectable two feet away but want to get through them as quickly as possible.

There are six main parts: the cloth of his uniform, his armor, any exposed skin, his gun, exposed metal and boots. For any metal parts I would recommend using Boltgun Metal for things like bayonets and Mithril Silver for any decorational pieces, like Aquilae. The rest, however, is up to you.

For my guardsmen I chose Bleached Bone armor, Mechrite Red cloth, bronzed/elf/tallarn flesh for skin (I like multiethnicity in my ranks) and bleached bone again for his boots.

As always we start by priming our figure. I tend to cheat a bit these days and use one of the color primers that Army Painter makes (in my case it's Skeleton Bone). This way I have already done half of my basecoating right from the get go.

 
The Unwashed Hordes

Next we need to basecoat any areas that are a different color than his armor. Use foundation paints for this part, as they go on opaque and can therefore easily cover up whatever color you primed with. Don't worry if you make mistakes- you can always clean up at the end.

Once you've cleaned up your base coating you can move on to washes. For the skin I use Ogryn Flesh, for everything else Devlan Mud. Devlan is a great wash that pretty much works on everything and makes it look more "real," and you can probably get away with Mud washing the entire model. You can also try using complimentary colors for the wash, such as Thraka Green on a red color.

After the wash has dried we need to highlight and drybrush using a lighter color. For drybrushing make sure to use a... well, dry brush. Be a bit more careful here but as always mistakes can be corrected.

 
Right: Washed and drybrushed but not highlighted. Left: washed, drybrushed and highlighted.

Once you've finished that step, you've finished your Guardsman! I would recommend doing each step for a squad at a time. That way you can keep on using the same paint for a period of time and get table-ready units all prepared at the same time.

For more info on painting Guard check out the painting section of the Imperial Guard archive on From The Warp or the Imperial Guard articles from Games-Workshop... just stay away from the tactica for the latter, as that's coming tomorrow!

Wednesday, September 29, 2010

SandWyrm Pattern Chimeras



A while back fellow blogger SandWyrm posted an excellent tutorial on creating set back Chimeras. I personally love the design as it makes our little chugs look much more like the badasses that they should be. It'll screw over your multilaser range a little bit, but cooler model trumps slightly limited functionality for me.

Tuesday, September 28, 2010

Photo Taking on the Cheap

So From The Warp is doing a collaborative post on photography and so I'm here to talk about making good quality photos with the minimum investment of time, money and effort possible. I personally want to spend those modeling and playing with my minis, not setting up photo boxes and whatnot.

Monday, February 8, 2010

Tip for Better Magnetizing

Over the weekend I put together a few converted veteran guardsmen for my Escalation League force and I wanted to do some magnetizing again. Having had so much trouble with the Valkyrie I knew that I needed to come up with a better way of ensuring a firm connection between the two magnets than just praying that the holes were the correct size. I also needed a better way of keeping polarities from getting mixed up, and something to help me deal with how tiny the magnets were would also help.

After thinking about it for a while, I came up with the following process:

 

First I drilled my first hole using my dremel and glued a magnet inside so that it was flush with the outside. Then, I placed another magnet on top as can be seen above.

I then took the piece that I was going to magnetize this to and drilled a hole in that one, checking every so often to see whether it fit the magnet yet. When it did, I put some glue in the hole, then stuck the exposed magnet into the hole while still attached to the first magnet. Then I simply slid the two pieces off of one another (DO NOT pull) and let the superglue take hold.


 
By keeping the two magnets attached while I was drilling the second hole I made sure that the final product would still have a nice, strong connection between the two parts. 
I then proceeded similarly with the other alternate weapons load outs, this time starting from the figure and placing the magnet on top that would go in the other weapon options.


So, if you're ever having trouble getting your magnets to stick (or even keeping the polarities in the right place), try keeping the magnets connected throughout the process- you'll see a much greater success rate in making that connection really secure. And if you drill too deep on the first or the second hole, don't worry- superglue or greenstuff should provide enough extra material to make sure that your magnet is in the right place.

Saturday, August 1, 2009

Making Do With Less: Meltaguns

A return to the series as I've started painting my army in earnest. The past two days I have spent making meltagunners for the SWS and Platoon Command Squad of Hearts platoon. Since I am a budget player (har har)I purchased the meltagun bitz packs instead of buying the metal special weapons troopers. This has two problems for me:

1) The hand on the meltagun is a space marine power armor glove; ok for Grenadiers or stormtroopers, but for a normal guy might pose an aesthetic problem.
2) Getting the hand and the gun on the trooper in a way that makes sense.

I've tried a few ways, often times unsuccessfully, with my vets, so this time I had a bit more experience going in. One way that I found worked fairly well was to use the Cadian infantry sprue and select the lasgun model that does not have the hand built into the gun. All I had to do was chop the gun and hand out of the weapon piece and I had two arms that were perfect to use for my trooper. Here's how they turned out:



I don't like these the most because of the glove; if I had another glove for the other hand that would be one thing, but... eh. You can also try leaving the hand on the gun, but I found that that ran into some interesting problems with the butt of the meltagun, as well as made it a bit harder to glue into place.

The other method, that I found worked very well was to take the grenade launcher pair of hands and use them to put the meltagun together. I imagine that it would work just as well for plasmaguns/you could probably use the flamer hands as well, as it is a similar configuration.

There are really only two steps. Step one is to cut off the arm and the pistol grip of the grenade launcher.



Step two is to cut off the butt and hand on the meltagun.



Then just attach the two together. Here's the finished model:



And here's a pic of him with the 4 other meltagunners I finished today: